Fencing & Tree Attachments - In Stock!
More Attachments available IN STOCK from NOTCH.
Is there an attachment we don't have in stock? Check our available products list from Beaver Valley.
Is there an attachment we don't have in stock? Check our available products list from Beaver Valley.
Magnum Tractor Wire Roller .... $1450
CAT 2. 65-125Hp. Includes 1 Split Spool
Designed to be used for barbed or smooth wire. We have had customers that have used this unit to roll cable and hose in their application.
• Hand spun all steel cone splitting reel (standard). Split reel holds 1/2 mile of barbed wire, or 1 mile of smooth wire.
• Replaceable poly impregnated polyethylene bushings on the drive shaft prevent wear. This bushing is proven to last for years of performance in the field.
• Standard reel is designed with four tie wires in four different positions as shown in our photos. These tie wires need to be in place before you start rolling wire. When the roll is full or you are done simply tie the wires before you remove the end part of the reel, this will keep your roll of wire tight and prevent spreading. This is also important as you need that roll to go back on that cone when you go to lay it back out.
• The Wire Guide Arm can be added to any new or used 3 point wire winder. This guide arm allows the operator to stand to the side of the unit and safely guide the wire onto the reel.
• The Winder is simple to use. Just park your tractor in one spot, tie a weight on the end of the wire and begin pulling toward you.
• ALWAYS have a weight on the end of the wire before you start rolling. This will keep the wire from whipping around loosely as it comes to the end, near the winder. A short piece of chain or any small item that can drag without catching will work fine. We used old window weights out of old houses for many years as they work great if you can find them.
• Always start slow and stop slow when rolling wire. The hydraulic design is a great help in allowing you to do that. Unit comes complete with a ball valve that is mounted next to hydraulic motor to be used to regulate speed or as a safety shut off.
• Always plug valve hose into power side of hydraulics.
• You should always have an operator on the seat of the tractor while in operation.
• Always use great caution when operating any type of wire winder as accidents can happen in a split second when not staying alert. Keep children away from unit at all times.
CAT 2. 65-125Hp. Includes 1 Split Spool
Designed to be used for barbed or smooth wire. We have had customers that have used this unit to roll cable and hose in their application.
• Hand spun all steel cone splitting reel (standard). Split reel holds 1/2 mile of barbed wire, or 1 mile of smooth wire.
• Replaceable poly impregnated polyethylene bushings on the drive shaft prevent wear. This bushing is proven to last for years of performance in the field.
• Standard reel is designed with four tie wires in four different positions as shown in our photos. These tie wires need to be in place before you start rolling wire. When the roll is full or you are done simply tie the wires before you remove the end part of the reel, this will keep your roll of wire tight and prevent spreading. This is also important as you need that roll to go back on that cone when you go to lay it back out.
• The Wire Guide Arm can be added to any new or used 3 point wire winder. This guide arm allows the operator to stand to the side of the unit and safely guide the wire onto the reel.
• The Winder is simple to use. Just park your tractor in one spot, tie a weight on the end of the wire and begin pulling toward you.
• ALWAYS have a weight on the end of the wire before you start rolling. This will keep the wire from whipping around loosely as it comes to the end, near the winder. A short piece of chain or any small item that can drag without catching will work fine. We used old window weights out of old houses for many years as they work great if you can find them.
• Always start slow and stop slow when rolling wire. The hydraulic design is a great help in allowing you to do that. Unit comes complete with a ball valve that is mounted next to hydraulic motor to be used to regulate speed or as a safety shut off.
• Always plug valve hose into power side of hydraulics.
• You should always have an operator on the seat of the tractor while in operation.
• Always use great caution when operating any type of wire winder as accidents can happen in a split second when not staying alert. Keep children away from unit at all times.
Danuser Python Wire Roller .... $480 -- IN STOCK
Will Work on Any Auger with a 2" Hex Shaft
Features:
• 3/4 Mile Barbed Wire
• 6 Mile Smooth Wire
• 2" Hex Connection
• Tie-wire Locations
• Tool-less Locking Pin
• Not for use on 3-point diggers
Will Work on Any Auger with a 2" Hex Shaft
Features:
• 3/4 Mile Barbed Wire
• 6 Mile Smooth Wire
• 2" Hex Connection
• Tie-wire Locations
• Tool-less Locking Pin
• Not for use on 3-point diggers
|
|
|
Python Wire Unroller .... $390
2" receiver/trailer hitch connection. Rebar and T-post straightening holes. Wire tensioning hooks. Rubber disc reduces backlash. Accepts most new spools of wire or bundles wound using Python Wire Winder. Toolless operation.
2" receiver/trailer hitch connection. Rebar and T-post straightening holes. Wire tensioning hooks. Rubber disc reduces backlash. Accepts most new spools of wire or bundles wound using Python Wire Winder. Toolless operation.
Bison Wire Roller for Fencing with Solid & Split Spools ............. $1195 IN STOCK
Extra Split Spool ............. $65
Extra Solid Spool ............ $65
Features:
Extra Split Spool ............. $65
Extra Solid Spool ............ $65
Features:
- Convenient for Rolling & Unrolling Smooth or Barbed wire out of the back of your Utility Vehicle bed.
- Powered by 6.5 HP OHV Engine
- Solid Reel Standard & Split Reel Available
- Simple Hand Clutch Design
DOUGLAS WELDING WIRE WINDER WITH SKID STEER MOUNT .............. $1300 --2-IN STOCK
ALSO AVAILABLE: DOUGLAS WELDING WIRE WINDER FOR BALE BEDS ........ $1300 - More on Order
ALSO AVAILABLE: DOUGLAS WELDING WIRE WINDER FOR BALE BEDS ........ $1300 - More on Order
Baumalight ISH3P Tree Puller .... SOLD OUT
The ISH3P tree puller is designed to grab hold and pull up to 4 inch diameter trees out of the ground, roots and all. By getting the roots and all, regrowth is greatly reduced. Designed for 4000 lb. to 8000 lb. class skid steers, the ISH3P will quickly clear an entire area, or selectively remove troublesome saplings, all from the comfort of your cab. The hydraulic jaw holds the trees tight while your skid steer arms let you uproot unwanted saplings quickly and cleanly.
The ISH3P tree puller is designed to grab hold and pull up to 4 inch diameter trees out of the ground, roots and all. By getting the roots and all, regrowth is greatly reduced. Designed for 4000 lb. to 8000 lb. class skid steers, the ISH3P will quickly clear an entire area, or selectively remove troublesome saplings, all from the comfort of your cab. The hydraulic jaw holds the trees tight while your skid steer arms let you uproot unwanted saplings quickly and cleanly.
NOTCH Heavy Duty Tree Puller with Wide Opening, NO Back Screen ....... $2250 -- IN STOCK
NOTCH Heavy Duty Tree Puller with Wide Opening and Back Screen ....... $2500 -- IN STOCK
NOTCH Heavy Duty Tree Puller with Wide Opening and Back Screen ....... $2500 -- IN STOCK
PRI Tree Puller
Max Opening 29.5" Dual Row 3/4" AR400 Teeth, Fully Enclosed Cylinder and Hoses, 3x8 3000# Cylinder, 56.25" Brush Guard Back, Made in Kansas
..... $2650 IN STOCK
Max Opening 29.5" Dual Row 3/4" AR400 Teeth, Fully Enclosed Cylinder and Hoses, 3x8 3000# Cylinder, 56.25" Brush Guard Back, Made in Kansas
..... $2650 IN STOCK
DANUSER "INTIMIDATOR" TREE / POST 34" OPENING PULLER W/SIDE TEETH ..... $3550 IN STOCK
DANUSER T3 POST DRIVER ....................... $2100 - IN STOCK
Optional Offset Quick-Attach plate. Extends 5' from center in 6" increments.
$750 by itself or +$500 instead of standard mounting plate at time of purchasing a new T3 driver.
$750 by itself or +$500 instead of standard mounting plate at time of purchasing a new T3 driver.
Designed for T-posts, the T3 can drive up to 3" diameter pipe. T3 Driver with Bracket - Impact force of 2,000 lbs. per hit, 6 hits per second. Includes Brackets, hoses, couplers, and mounting plate.
|
|
Danuser SM40 Hammer Post Driver
DA21003- With Grapple and Tilt .... $8000 Cash IN STOCK!
Click HERE to watch video!
• Free fall weight design
• Hammer weight does not strike the top of posts
• Grapple option allows one-person operation by picking up the post from the ground
• Tilt option allows up to 20 degree to the left or right
• Top of the post is contained in the machine, preventing the post from kicking out
• T-Posts, Pipe Fence, Sign Posts, Guard Rails, Railroad Ties, Fence Posts
Click HERE to watch video!
• Free fall weight design
• Hammer weight does not strike the top of posts
• Grapple option allows one-person operation by picking up the post from the ground
• Tilt option allows up to 20 degree to the left or right
• Top of the post is contained in the machine, preventing the post from kicking out
• T-Posts, Pipe Fence, Sign Posts, Guard Rails, Railroad Ties, Fence Posts
Baumalight ST324 ...... $5750 - On Order
Small Fixed Compact- This fixed frame hydraulic tree spade is ideal for smaller skid steers. The ST324 Small Fixed Compact tree spade features three blades to give you the digging and root ball compacting action necessary for cleaner and more viable transplants.
Small Fixed Compact- This fixed frame hydraulic tree spade is ideal for smaller skid steers. The ST324 Small Fixed Compact tree spade features three blades to give you the digging and root ball compacting action necessary for cleaner and more viable transplants.
- 2" Evergreen
- 1.5" Hardwood
- Wheeled Skidsteer - 5000 lbs
- Tracked Skidsteer - 4500 lbs
